Graflex Grand Master – Complete Chassis Kit (Brass)

1.629,00

Only 1 left in stock

Complete Graflex Grand Master chassis kit.

It includes a complete chassis, with accessories and all electronic components to install it. (see list below)
For CFX Soundboard and full brass chassis to be weathered

Notes:
– Tools to perform the conversion are not supplied.
– Heatshrink tubing and weathering chemicals are not supplied.
– Removable Keepower batteries not included (due to shipping restrictions).
– This is an expert level build, for experienced installers. By buying you acknowledge having read this page entirely.

Please read our Terms and Conditions.

Shipping: will ship in approx. 2 to 3 weeks.

Return policy: No return accepted on this item.

Order cancelation policy: This order cannot be canceled once shipped.

 


 

Parts included in this kit:
CHASSIS
Complete Grand Master Chassis parts, including blade holder and 2 crystals.
For CFX and all metal parts in natural brass to be weathered, except Part16 in copper.

COMPONENTS:

– 1 x Crystal Focus 10 MK2 soundboard
– 1 x OLED Screen (New version – KR-Sabers OLED)
– 1 x Bluetooth board
– 1 x Motor
– 1 x KR 3W 28mm Bass Speaker
– 1 x KR Shtok ECO NPXL Connector (hilt side)
– 1 x KR Shtok ECO NPXL Lens
– 1 x 7/8″ NPXL Connector holder
– 1 x set of resistors (4) for tangible font selection
– 1 x NPXL Data line resistor
– 1 x set of 0 ohm SMD jumpers (6) for blue accent leds
– 1 x SMD resistor for red 3mm led
– 7 x 0804 pre-wired SMD LEDs
– 5 X single pixel accents
– 1 x 3mm red accent LED
– 1 x High Amp Kill Switch
– 2 x brass tactile switch (duplicate switch on soundboard module)
– 2 x blade holder switches (1 brass tactile, 1 slim profile)
– 1 x Bluetooth kill switch
– 2 x Battery contacts (pos and neg)
– 2 x Bulgin Pins 10A set (Male and Female)
– 6 x Bulgin Pins 1A set (Male and Female)
– 2 x Mill-Max pins (10 pins bar each – to be cut)
– 1 x Mill-Max Socket (10 sockets bar – to be cut)
– 1 x set of Brass M2 screws (2)
– 1 x set of Aluminium M2 screws (2)
– 1 x set of Black M2 screws (2)
– 1 x 4-40 retention screw (NPX connector)
– 1 x 4-40 screw (Blade retention)
– 3 x 4-40 hex nuts
– 10 x 3mmOD 2mm thick
– 34 x 2mmOD 2mm thick
– 30 x 2mmOD 1mm thick
– 1 x set of PTFE Wires (22awg, 24awg, 28awg, 30awg)
– 1 x copper electric cable (for Arc Reactor)
– 1 x 4-40 brass threaded rod
– 1 x set of 4mmOD tubes
(brass approx 55mm length, aluminium approx 100mm length, copper approx 145mm lenght – to be cut)
– 1 x set of 2mmOD tubes (copper and brass – to be cut)
– 1 x copper 1mmOD Tube (to be cut)
– 1 x brass 1.5mmOD rod (approx 93mm length – to be cut)
– 1 x nickel 1mmOD rod (to be cut)
– 1 x nickel 0.5mmOD rod (helps to sand and clear the 1mmOD tube)