Other Chassis for Starkiller TFUI

Korbanth Starkiller TFUI (2019) Chassis

Parts Details:

(for 2019 hilt version only, not compatible with 2021 hilt)

1- 3D printed Chassis parts:

Shapeways Shop Section ⇒ C7 – Korbanth
The Saber Armory shop =>ECO Chassis 
PadawanVariant 1 Available
Padawan Variant 2Available
ECO Chassis and PIY Files Available


2 chassis variants are available.
Prices: Depends on the material and Shapeways current rates – add the part into the cart to estimate final cost
Install Level: Beginner
– Var1 for 21700 battery and recharge port (accessible through the pommel insert).
=> All.In.One Var1 Chassis: korbanth-starkiller-lightsaber-chassis-var1

– Var2 for removable 18650 battery
=> All.In.One Var2 Chassis: korbanth-starkiller-lightsaber-chassis-var2

– Optional, crystal chamber add-on to add details into the open crystal chamber
=> CC Add-on: korbanth-starkiller-cc-add-on


=> ECO Chassis: korbanth-sk-fdm-eco-chassis

2- Additional chassis parts:
Most of the chassis parts needed for our chassis are available at The Saber Armory.
Local hobby stores or online store (as well as eBay) are a good source for parts.
You can also be inventive and add any custom parts, wire mesh, paint job or else to your chassis to give it an unique look!
The Var2 chassis uses the following parts:
⇒ 1.5mmOD rods for the soundboard cover.

3- DIY empty hilts:

 Available on Korbanth website

4- Electronic components and blades:
Saber electronic components are basically more or less similar from one saber to another. You’ll need a main Led, a Battery, a recharge port, one or two switches, a soundboard, accent leds, a speaker and wires. Then the blade is the last part of your saber, they are usually made from PolyCarbonate tubes + tip.
You can find most of what you’ll need at The Saber Armory. Some components can also be found at The Saber Bay on Etsy. Local electronic shops or online stores like Digikey are also a good source.
Soundboard, all major soundboards with Multiboards Adaptive Chassis (ProffieBoard, NB, Prizm, CF9, NEC I3)
Battery, Var1: 21700 battery, Var2: keystone 18650 holder
Recharge Port, Var1 only, 2.1mm port (custom kill key included)
 On/Off switch, Var2 only, high amp slider switch
 Main Led, Tri-Cree XPE-2 or Neopixel.
 Heatsink, 1in heatsink  or Neopixel 1in connector.
 Switches, 2 tactile switches
 Speaker, 28mm bass speaker
 Wires, PTFE wires available at The Saber Armory
– Tri-Cree install => 30awg for eveything
– Neopixel install => 32 awg wires for everything except Battery and Neopixel strip + and – (24awg PTFE).
 Heat shrink tubing, to protect your solder joints.
 1″ OD blade or 7/8″ OD blade (with 1″ adapter) for the main blade.


None yet

Quick Install Guide: 

(step by step)

– These instructions will details the install procedure as much as possible. GOTH-3Designs cannot be held responsible for any mistakes made by DIYers.
– Always wear protective gear when working on install (gloves, eye protection, …), GOTH-3Designs cannot be held responsible in case of accident.

Note 1Use small wires to make your install easier
=> for Tri-cree install 30awg for main wires and 32awg  for accent leds and switches are highly recommended
=> for Neopixel PTFE 24awg for main wires (battery and led strip + and -), and 32awg  for accent leds and switches are highly recommended

Note 2: These instructions will not cover how to wire the soundboard, make sure to learn how to by reading the manual. make sure to test your install along the way! Making sure everything works after important steps is better than having to dismount everything because something wasn’t wired properly.

Note 3: MultiBoards Adaptive Chassis 4.0: