– Return to Luke V2 Chassis Line-Up –

Parts Details:

1- ROTJ Luke V2 Hilt:

 Contact Solo’s Hold

2- 3D printed Chassis parts:

All.In.One (Plastic – Recommended Black)

Contains: Main Chassis, switch cover, board cover, switch plunger and kill key.
For CF and PC: v2-02-1-cf7-5-pc3-5-knight-chassis-all-in-1
For PRIZM: v2-02-1-prizm-knight-chassis-all-in-1
For I2: v2-02-1-i2-knight-chassis-all-in-1

3- Additional chassis parts:

Chassis parts can be found in local hardware stores as well as on the web. eBay models shop is also a good source internationally to find small parts, check eBay model shops for instance: OmniModelsCave Spring Hobby, ……..
You can also be inventive and add any custom parts, paint job or else to your chassis to give it an unique look!
Here is a list of parts needed to install the above chassis:
⇒ Brass or copper rods – 1.5mm max OD –  To be cut with the following length: 2x56mm, 1x50mm (total length 160mm) – (note for the Prizm version, instead of 2x56mm and 1x50mm, you can cut 3×56).
 Crystal – real quartz – approx 19mm max length, and 10mm max OD

4- Electronic components and blades:

Saber electronic components are basically more or less similar from one saber to another. You’ll need a main Led, a Battery, a recharge port, one or two switches, a soundboard, accent leds, a speaker and wires. Then the blade is the last part of your saber, they are usually made from PolyCarbonate tubes + tip.

You can search these parts with the following suppliers: Solo’s Hold, The Saber ArmoryElegant WeaponsJQ-Sabers

Soundboard, the “heart” of our sabers is the Soundboard, here are the 2 major Soundboard producers:
Plecter Labs – from the entry level Nano Biscotte to the high end Crystal Focus.
Naigon Elelctronic Creations – from the entry level Spark 2 to the high end I2.
Battery, 18650 battery for 3.7v or 2×16340 for 7.4v.
⇒ Recharge Port, 2.1mm port is used on this chassis (kill key included in the chassis kit).
 Battery charger, according to the battery voltage used.
 Main Led, Tri-Cree XPE-2
 Switches, are included with the hilt.
 Speaker, 28mm Speaker flat premium only
 Accent Leds, 5mm led for the Crystal Chamber recommended (if RGB, read your soundboard manual to select between common anode or common cathode led), 3mm leds for the others.
 Wires, 30awg wires are recommended on most our 3D Printed chassis. We are buying them from this eBay seller.
 Heat shrink tubing, to protect your joints.
 RICE port 
– a RICE port can be added to the CF and Prizm chassis. Ex TCSS..
 7/8″ OD Blades only.

 


 

DIY Instructions:

Note 1This Knight chassis is very similar to the Master version (except for the Crystal Chamber assembly). Please follow the Master chassis DIY instructions to learn how to install it (and just skip the Crystal Chamber steps).

⇒ MASTER Chassis DIY Instructions

Note 230awg wires and smaller are mandatory for this install (30awg for main wires and 32awg  for accent leds and switches are highly recommended).

Note 3:  These instructions will details the install as much as possible. GOTH-3Designs cannot be  held responsible for any mistakes made by DIYers tho. Thanks to read the full instructions before starting your install. Commission an installer to build the hilt for you, if you feel unsure about what to do.

Note 4: About the Kill Key. It is recommended to sand a bit the side of the kill key “on/off” slot, in order to make them more round and to turn better in the recharge port. (as a reminder, this slot allow to start / stop the saber without removing the kill key).

Note 5: Recharge port wiring reminder:

Loading...
Facebook Messenger for Wordpress